Guide

Pre-shipment inspection for amenity orders: when and how

A pre-shipment inspection checks a finished, packed amenity order at the supplier's site before it leaves, using a sample drawn under an agreed plan. It is most worthwhile for first orders, large or international shipments and products with a history of problems, because fixing a fault before dispatch is far cheaper than after delivery.

By Hemang Jain, Founder, Anadoris

What is a pre-shipment inspection?

A pre-shipment inspection is a check of finished goods carried out once production is complete and most of the order is packed, before it is dispatched. An inspector, who may be from your company, a third-party inspection firm or the supplier's own quality team under agreed rules, draws a sample of cartons and units and checks them against the specification, approved samples and packing instructions.

It is different from the supplier's own release testing. Release testing confirms the batch meets its specification in the laboratory. A pre-shipment inspection looks at the order as you will receive it: the right products, correctly labelled, packed and marked, in the right quantities. The two complement each other.

The value of inspection lies in timing. Once goods are on a ship or in a truck, every correction becomes slow and expensive: return freight, customs paperwork, rework at a distance and an empty store room in the meantime. At the supplier's site, the same correction may take a short sorting exercise or a relabelling run.

When is a pre-shipment inspection worth doing?

  • First orders with a new supplier or a new branded range.
  • International shipments, where returning faulty goods is slow and costly.
  • Large orders, where a fault would affect many properties.
  • Products with a history of defects or recent corrective actions.
  • Time-critical orders, such as stock for a hotel opening, where there is no time to replace a faulty delivery.

For a stable supplier with a good record on routine reorders, inspection may be occasional rather than every time. Many buyers move from inspecting every order to inspecting a selection as confidence grows, and step back up after any problem.

Weigh the cost of inspection against the cost of a failure reaching your properties. For a small, local reorder of a proven product, inspection may cost more than it saves. For a first container of a new branded range bound for several countries, it is usually cheap insurance.

STAY by Anadoris concept: seafoam oval pump bottles in a granite outdoor vanity, ocean and palms
Seychelles granite island villa

How does sampling for inspection work?

Inspectors rarely check every unit. Instead, they use a sampling plan that sets how many units to inspect from an order of a given size and how many defects of each type are acceptable. Many buyers use plans based on international acceptance sampling standards, often referred to by the term AQL (acceptance quality limit).

Defects are usually grouped into three classes. Critical defects could cause harm or breach regulations, such as a wrong ingredient label; normally none are accepted. Major defects would likely cause a complaint or make a unit unusable, such as a leaking closure. Minor defects are cosmetic and unlikely to bother a guest, such as a small scuff on a carton. Agree the plan, the defect classes and the acceptance limits with your supplier in advance, in writing, so the inspection result is not a surprise to either side.

What does an amenity inspection check?

This table lists typical checks in a pre-shipment inspection of liquid amenities.

CheckExamples
Quantity and packingCarton count, units per carton, pallet build, carton marks
AppearanceColour, clarity, foreign particles, compared with reference
FragranceMatches approved standard
FillWeight or volume of sampled units within tolerance
Closure and leakageTorque, seal, inverted or pressure leak test
Printing and labellingArtwork matches approval, legible batch code, placement
FunctionPumps prime, flip caps open and close, tubes squeeze
DocumentsCOA present and matching the batch

What should an inspection report include?

  1. Order and product details, batch codes and inspection date.
  2. Sampling plan used and number of units checked.
  3. Results for each check, with defects classified as critical, major or minor.
  4. Photographs of packed goods, carton marks and any defects.
  5. A clear outcome: pass, fail or hold pending a decision.
  6. Inspector's name and organisation.

A good report lets someone who was not present understand exactly what was found. Ask for it promptly so a decision can be made before the shipping booking is affected.

Share the report with the supplier straight away, including for a pass. Suppliers learn from minor findings too, and an open report builds trust that the inspection is about the product, not about catching anyone out.

STAY by Anadoris concept: cobalt blue ribbed pump bottles in a white tile, lemons, dramatic distant sea
Amalfi cliffside suite

What happens if the inspection fails?

Agree in advance what follows a failed inspection. Options include sorting the order to remove defective units, reworking such as relabelling, replacing the affected part of the order, or remaking the batch. The supplier should then present the order for re-inspection. Who pays for re-inspection is worth stating in your agreement.

Use a failed inspection as an input to corrective action, not only as a reason to sort stock. If the same defect appears at inspection more than once, the supplier's own controls need attention.

To discuss a buyer or third-party inspection at the STAY by Anadoris facility in Ambala, use the contact form, and see the glossary for terms such as AQL.

Record every inspection result in the supplier file, pass or fail. Over time, the results show whether inspections can be reduced or need to increase.

Questions on this topic

What does AQL mean?

Acceptance quality limit: a term from acceptance sampling standards describing the defect level that a sampling plan treats as acceptable for a given order size.

Who carries out pre-shipment inspections?

Your own staff, a third-party inspection company or the supplier's quality team under agreed rules. Third-party inspectors are common for international orders.

Does an inspection replace the supplier's testing?

No. The supplier's release testing checks the batch against specification; the inspection checks the packed order. Both are useful.

Keep reading

Ready when you are

Tell us about your space. We will send samples.

CallRequest samples